船舶结构名称
周记600-人大代表的职责
船舶结构名称
1.1船长1)总长Loa:length of
overall2)垂线间长
Lbp:length between
perpendiculars3)登记船长L:
registered
length4)干舷长Lf:freeboard
length5)船舶分
舱长度LS:subdivision length6)艉垂线:aft
perpendicular7)
艏垂线:forward
perpendicular8)后端点:aft end point9)
挪威规范,英国规范:Oslo Rules, UK Rules10)前端点:
fore
end point11)美国规范:USA Rules12)艏楼甲板:F’cle
Dk13)日本规范: Japanese
Rules14)艏柱:stem15)水线
长:length of water
line16)干舷长前端点: forward end of
freeboard
length1.2 船宽1)登记船宽B:registered
breadth2)上甲板
Upp Deck3)角隅圆弧的断点 :
termination of corner
radius4)干舷船宽Bf : breadth of ship
for
freeboard5)分舱船宽Bs : subdivision breadth of
ship1.3 型深(D)depth1.4 吃水d: draught or draft1.5
干舷: freeboard1.6 吨位及舱容 tonnage and cargo
capacity总吨 gross tonnage 净吨 net
tonnage苏伊士运
河吨位 Suez Canal tonnage巴拿马运河吨位
Panama
Canal tonnage排水量 displacement载重吨
deadweight
国家吨位 national tonnage国际吨位
international tonnage
包装货物舱容 bale capacity谷物舱容
grain capacity外板
shell plating 护肋材
sparring谷物容积限度 grain capacity
捆包容积限度 limit of
bale capacityg表示谷物容积 g
indicates grain
capacity b表示捆包容积 b indicates bale
capacity底部垫木
bottom ceiling1.7船速 speed1.8 船
型系数 block
coefficient细长型 fine form 肥大型 full form
方形系数block coefficient (Cb)中横剖面系数 midship
coefficient (Cm)棱形系数 prismatic coefficient
(Cp)水线面
系数 water plane coefficient
(Cw)1.9描述船舶动态及静态
的词汇 terms to describe the
dynamic[dai’nAmik]
conditions and static
positions纵倾trim 艉翘 trim by stern
艏翘 trim by
head无纵倾状态 even keel (non-trimmed
condition)横倾
heel or list 船体运动 ship motion横摇
rolling纵摇
pitching艏摇 yawing垂荡 heaving横荡
swaying纵荡
surging1.10描述船体构件受力及变形的词
汇 describe the
movement of hull structural member弯曲
bending
扭曲 twisting 屈曲buckling振动 vibration 剪切
sheering
横摇rolling 强摇 racking1.11其他基本词汇 (1)1)
左舷 port
side 2) 右舷 starboard side3) 纵向 longitudinal
4)
横向 transverse5) 水平 horizontal 6) 垂直 vertical 7)
中心线 centre line (CL & )8) 舯 midship or
amidships
(expressed by symbol )9) 船中区域
midship part (0.4L ~
0.5L)10) 船首 bow 11) 艏柱
stem 12) 艏部 bow part or
fore part13)
艏垂线 fore perpendicular (FP)14) 艉柱
stern 15)
艉部stern part or aft part16) 艉垂线 aft
perpendicular (AP)17) 尾端 ends: these normally
signify
the end parts of the hull of a ship
with 0.1L通常是指自船尾
端始的0.1L的范围18) 基线 base line
(BL): normally the
keel line 通常是指龙骨线19) 肋骨间距
frame space 20)
肋骨线 frame line21) 船体围长 girth
length: the length
measured at the transverse
section of the hull of a ship
from gunnel to
gunnel 在船体横截面上从一侧的船舷上沿
量取到另一侧的船舷上沿的距离22) 龙骨上面
top of keel
23) 折角线 knuckle line (KL) 24) 折角点
knuckle point25)
舷弧 sheer 26) 艏舷弧 fore sheer
27) 艉舷弧 aft sheer
28) 梁拱camber29)甲板内倾 tumble
home 30) 外飘
flare31)舭部升高 rise of floor 32)平行部
parallel part1.12
其他基本词汇(2)1) 船桥甲板上缘 top of
bridge deck beam
2) 船桥楼外缘 outline of bridge
enclosure3) 上甲板梁上缘
top of upper deck beam 4)梁拱
camber5) 主甲板的内倾
tumble home at upper deck6)
船桥甲板的内倾 tumble
home at bridge deck7) 上甲板边
upper deck at side 8) 船
中心线 centre line of
ship9) 舭部 bilge part 10) 平板龙骨
的一半 half-side
dimension of flat portion at keel11) 船中
船桥甲板的型深
moulded depth to bridge deck12)
船中主
甲板处的型深 moulded depth to upper
deck13) 船中型吃
水 moulded draught1.13 线型 lines1)
横剖线图 body
plan 2) 纵剖线图 profile or sheer plan
3)半宽图水线
half-breadth plan1.14其他图纸文件 other
plans and
documents1) 除线型图之外,下列图纸被称为关键图(key
plans):总体布置图 general arrangement 中横剖面图
midship section钢材构造图 construction profile
外板展开
图 shell expansion2) 其他关键图以外的船体图纸被称为船
厂图
(yard plan):(1) 船体方面艏柱、艉柱、螺旋桨柱和舵结
构 stem, stern
frame, propeller post and rudder甲板结构
图 deck
plans 单底、双底结构图 single bottom and double
bottom水密和油密舱壁结构图 watertight and oil tight
bulkheads上层建筑端壁图 superstructure end
bulkhead船
首、船尾、船底部抗拍击结构图 arrangement to resist
panting in both peaks and their vicinity
[vi’siniti] 邻近, 接近
支柱和甲板纵桁图 pillars and deck
girders 轴隧图 shaft
tunnels锅炉、主机、推力轴承、中间轴承、发电机和其
它
重要辅机基座图Seating of boiler, engine, thrust and
plummer blocks dynamos 发电机机舱棚图 machinery
casings长甲板室结构图 long deckhouse桅杆、桅室和绞车
平台结构图
masts and mast houses and winch platforms
泵布置图
pumping arrangements甲板装原木时绑扎装置布
置图
timber deck cargo security arrangements防火构造图
construction for fire protection消防布置图 plans
showing
fire extinguishing arrangement逃生路径布置图
plans
showing escape routes舱室路径图 plans showing
arrangement for access of tank and space(2)
轮机方面机
器处所布置图 machinery arrangement of machinery
space
船内通讯系统图 diagram for internal
communication
system主、辅机图 main and auxiliary
engines动力传动齿
轮、轴系及螺旋桨图 power transmission
gears, shafting
and propellers锅炉及压力容器图 boiler
and pressure
vessel辅机和管系图 auxiliary machinery
and piping操舵装
置图 steering gear自动控制及遥控装置图
automatic and
remote controls备件 spare part
电气装置 electrical
installations 船桥视界 navigation
bridge visibility(3) 其他
图纸文件船体轮机设计说明书
specifications for hull and
machinery船中横剖面模数计算书 calculation sheets for
minimum athwartship (横越) section modulus (模数)
in way
of the midship part防腐式样书 corrosion
prevention
scheme 稳性计算书 stability calculation
sheets破舱稳性
计算书 damage stability calculation
sheets装载手册
loading manual 绑扎手册 security
manual1.15 静水力曲
线 hydrostatic curves浮心距基线高度
centre of buoyancy
above base line
(KB)浮心距船中 centre of buoyancy from
midship
(B)漂心距船中centre of floatation from midship
(F)
每厘米吃水吨数 tons per one centimeter immersion
(TPC)
每厘米纵倾力矩 moment to change one centimeter
(CTM)
水线系数 water plane coefficient (Cw)纵稳心距基线高
longitudinal metacentre above base line
(LKM)横稳心距基
线高 transverse metacentre above base
line (KM)棱形系
数 prismatic [priz’mAtik]
coefficient (Cp)垂直棱形系数
vertical prismatic
coefficient (Cvp)方形系数 block
coefficient
(Cb)型排水量 displacement in tons excluding
appendages (附件,附属物)总排水量 displacement in tons
including appendages船体湿表面面积 wetted surface
area (W.S.)1.16 稳性 stability1)静态稳性 intact
stability 2)
动态稳性 dynamic stability3)稳性判据
stability criteria (标
准) 4)稳性曲线 stability
curves5)倾斜试验 inclining test
6)重心高度 KG (height
of centre of gravity)7)稳心高度
KM (height of
metacentre)8)初稳性高度 GM 9)静稳性力
臂 GZ10)自由液面的影响
free water effect11)大倾角稳
性 stability at a large
inclination angle12)稳性十字曲线
cross curves of
stability13)纵向稳性 longitudinal stability
14)横向稳性 transverse stability15)破舱稳性 damage
stability 16)浸水计算 flooding calculation17)浸水概率
flooding probability 18)分舱
compartment19)生存条件
survival requirement
20)最终状态 final stage21)生存概
率 survival
probability 22)分舱指数 subdivision index23)
处所渗透率
permeability of a space24)许用GM0曲线
permissible
GM0 curve1.17 波浪 wave斯托克波 stokes
wave 正弦波 sine
wave 摆动波 trochoidal wave船行波
wave generated by
ship sailing 散波 divergent wave船尾
横波 stern
transverse eave 船首横波 bow transverse
wave
1.18 船体强度 strength of ship船体垂向弯曲最终强度
vertical bending ultimate strength船体梁强度 hull
girder
strength 纵向强度 longitudinal strength纵向弯距
longitudinal bending moment 剪切力 sheering
force中拱
hogging 中垂 sagging静水弯距 longitudinal
bending
moment in still water (Ms)波浪弯矩 Mw(+)
and Mw (-)
wave induced longitudinal bending
moment横向强度
transverse strength 扭转强度 twisting
strength局部强度
local strength 失稳强度 buckling
strength受压失稳强度
compressive buckling
strength剪切失稳强度 sheer
buckling strength直接强度计算分析
direct strength
calculation analyzing疲劳强度
fatigue strength疲劳强度
解析、评价 fatigue strength
anlyze, assessment应力集中
stress
concentration波浪周期 wave period 随浪 following
wave 顶浪 heading sea 横浪 beam wave波浪载荷 wave
load 垂向波浪弯距 vertical wave bending
moment波浪变
动压 hydrodynamic
(水力,流体动力学)pressure舱室内压
internal pressure 许用应力
allowable stress最小弯距
Wmin 剖面模数 section
modulus惯性矩 moment of
inertia强度连续性 continuity
of strength 板架、板单元
plate panel1.19
船体尺寸限制Panama 圣。劳伦斯水路 St.
Lawrence Seaway马六甲海峡
Strait of Malacca1.20 造
船用材料1)轧制钢材 rolled
steel板材 plate 型材 shape
扁钢 flat bar (FB) 球扁钢
bulb plate (BP)角钢 angle (A)
槽钢 channel (C) T型钢
T bar 铆钉钢 rivet bar圆钢
round bar 半圆钢 half round
bar2)组合型材 built-up
shape3)材质 material普低钢(软钢)
mild steel (MS):
grade A, B, D, E高强钢 high
tension steel (HT): grade A32,
D32, E36, D36,
A40, D40, E40低温钢 low-temperature
steel: L24A,
L24B, L27, L33, L37, L2N30, L3N32, L5N43,
L9N53, L9N60不锈钢 stainless steel复合钢 clad
steel铸
钢 steel casting锻钢 steel forging铝合金
alumimum alloy
船体通用部件名称2.1 龙骨 keel1)方钢龙骨 bar
keel (用
于小型船舶) 2)龙骨翼板 garboard strake3)箱型龙骨duct
keel, 和双层底构造的管弄(pipe tunnel)兼用4)内底板 tank
top 5)平板龙骨 flat plate keel, keel
plate2.2 外板 shell
plating龙骨板 keel plate
,固定缩略为K; 舷顶列板 sheer
strake , 固定缩略为S舭部外板 bilge
strake or bilge plate
船底外板 bottom shell
plate船首底板 forward bottom
plate 舷侧外板 side shell
plate2.3 舭龙骨 bilge keel平钢
flat bar2.4 肋骨
frame1) 按设置的方向分:纵向肋骨
longitudinal frame 横向肋骨
transverse frame2) 按设置的
部位分 frame termed by
their location(1) 艏尖舱肋骨 fore
peak frame (2)
艉尖舱肋骨 aft peak frame(3) 货舱肋骨
hold frame (4)
机舱肋骨 engine room frame(5) 甲板间肋
骨 tween deck
frame (6) 上层建筑肋骨 superstructure
frame(7) 倾斜肋骨
cant frame (8) 巡洋舰尾型肋骨 frame
of cruiser
stern(9) 抗拍击(砰击)肋骨 panting frame (10)
前端肋骨
fore end frame3) 按重要程度、构件尺寸的大小分:
箱型肋骨 box type
frame 特设肋骨、强肋骨 web frame 普
通肋骨 ordinary
frame2.5 肋骨间距及保护 frame space,
protection for
frame1) 横置护肋材 horizontal sparring 2)
垂直护肋材
vertical sparring2.6 底部构造1) 单底构造
single bottom
construction(1) 平板龙骨 flat plate keel (2)
中心线内龙骨 centre keelson [‘kelsn](3) 面板 rider
plate
(4) 肋板 floor plate (5) 侧内龙骨 side
keelson(6) 外底板
bottom shell plate (7) 舷侧外板
side shell plate(8) 肋骨
frame (9) 舭肘板
bilge bracket2) 双层底构造 double
bottom
construction(1) 侧纵桁 side girder (2) 水密肋板
watertight floor (3) 开放肋板 open floor(4) 实体肋板
solid
floor (5) 内底板 tank top (6) 中心线板 middle
line
strake(7) 肋骨 frame (8) 缘板 margin plate
(9) 中心线纵
桁 centre girder(10) 双层底舱顶板 tank top
plate (11) 缘
板 margin plate(12) 中线列板 middle
line strake (13) 肋
骨肘板 frame bracket(14) 舱边肘板
tank side bracket (15)
撑角板 gusset plate(16)
减轻孔 lighting hole (17) 透水孔
limber hole (18)
透气孔 air hole(19) 人孔 manhole (20)
流水孔 limber
hole (21)内底板 tank top(22) 外底板
bottom (23) 扶强材
stiffener(24) 框架肋板 skeleton foor
(25) 反面肋骨
reverse frame(26) 撑材 strut (27) 侧纵桁
side
girder (28) 轴板 bracket(29) 角撑板 gusset plate (30)
舱缘肘板 tank side bracket(31) 过梁孔 slot (32) 过焊孔
scallop (33) 补板 collar plate(34) 补板 collar
plate (35)
水密补板 W.T. collar plate (36) 水密板壁
W.T. plate(37)
扇形过焊孔 scallop2.7 船首构造 bow
construction1) 防撞
舱壁 collision bulkhead 2) 扶强材
stiffener 3) 上甲板梁
upper deck beam4) 船首甲板梁
forecastle deck beam 5)
第二层甲板梁 2 nd deck
beam6) 防挠梁 panting beam 7)
船侧纵通材 side
stringer8) 中心线纵桁 centre girder 9)
肋板
floor 10) 肋骨 frame 11) 支柱 strut12) 制荡板
wash
plate 13) 链齿轮 sprocket wheel 14) 艏楼 F’ cle15)
上甲板 upper deck 16) 第二甲板 2nd deck 17) 锚链舱
chain locker18) 制链器 chain compressor 19) 甲板法兰
deck flange20) 锚链导管 chain pipe 21) 锚链管 hawse
pipe 22) 锚唇 bell mouth23) 污水井 bilge hat 24)
舱顶板
tank top 25) 强胸梁 panting stringer26) 十字撑材
tie bar
27) 强胸横梁 panting beam 28) 肋板 floor29)
支柱 strut
30) 面板 flange 31) 水手长仓库 boatswains
store32) 第
一层强胸梁 1st panting stringer 33) 侧强胸梁
side
stringer34) 球鼻艏 bulbous bow35) 船首分类:切水船首
cut water bow 垂直船首 upright bow前倾型艏 raked bow
冲撞船首 ram bow2.8 船尾构造 stern construction1) 龙骨
keel 2) 桨柱 propeller post 3) 轴毂 boss 4) 弧拱
arch5)
艉柱 stern post 6) 下舵钮 gudgeon 7) 舵托 heel
piece8)
深肋板 deep floor 9) 船尾肋板 transom plate
10) 斜肋骨
cant frame11) 艉尖舱壁 after peak bulkhead
12) 逃生通
道 escape trunk13) 轴隧凹处 tunnel recess
14) 艉尖舱
aft peak tank15) 舵杆管 rudder stock
trunk 16) 中心纵桁
centre girder 17) 肋板 floor18)
内底板 inner bottom plate
19) 轴隧侧肋骨 tunnel side
frame20) 轴隧上板 tunnel top
plate 21) 机舱肋骨 engine
room frame22) 二甲板 second
deck 23) 直梯
vertical ladder 24) 艉轴 tail shaft25) 横壁
直梯
bulkhead vertical ladder 26) 外板 shell plate27)
支
撑 strut 28) 艉轴架 shaft bracket2.9 甲板 deck1)
按强度
分 termed by longitudinal strength强度甲板
strength deck
有效甲板 effective deck 平台甲板
platform deck2) 按位置
分 termed by location上甲板
upper deck 下甲板 lower
上甲板以上甲板 deck above upper
deck船桥甲板 bridge
deck 游步甲板 promenade deck救生艇甲板
boat deck
航海甲板 navigation deck3) 按目的分 termed
by purpose
暴露甲板, 风雨甲板 exposed deck, weather
deck遮蔽甲
板 shelter deck 干舷甲板 freeboard deck 吨位甲板
tonnage deck4) 钢质甲板再细分连接甲板 cross deck 最
外甲板
stringer deck舷弧板 gunwale angle, or stringer
angle 可移甲板 portable deck元角舷弧 rounded gunwale
直角舷弧 square gunwale 舷顶列板 sheer strake2.10
舱
口围板, 舷墙, 栏杆 hatch coaming, bulwark and
guardrail1) 舱口围板 2) 水平扶强材 horizontal stiffener
3)
半圆钢 half round bar4) 舱口围肘板 coaming stay or
bracket 5) 甲板梁 deck beam6) 舷墙 7) 舷墙端部
bulwark end 8) 伸缩接头 expansion joint9) 光顺圆角过渡
wellrounded & smooth surface10) 缆绳孔 mooring
hole 11)
椭圆孔 oval hole12) 舷墙中直部 bulwark in way
of ship
middle part13) 舷墙板 bulwark
plate 14) 舷墙肘板
bulwark stay15) 舷墙面板 bulwark
top rail 16) 泄水开口
freeing port17) 栏杆 guardrail
18) 立柱 stanchion2.11 梁,
桁, 柱 beam, girder,
pillar1) 梁 beam(1) 按所在位置分上
甲板梁 upper deck beam
第二层甲板梁 second deck
beam船首露天甲板梁 forecastle deck
beam救生艇甲板梁
boat deck beam 艉斜梁 cant beam 船尾横梁
transom
beam舱口端梁 hatch end beam 立柱 pillar 纵桁
girder
舱口 hatch 横壁bulkhead(2) 按构件的大小分普通横梁
ordinary beam 强横梁, 特设横梁 strong beam or web
beam(3) 按其方向分① 横梁 transverse beam全通横梁
through beam (fitted from side to side
从船的一侧到另一侧)
半通横梁 half beam (cut at hatch opening
在舱口处切
断)② 纵梁 longitudinal beam2) 甲板桁 deck
girder3) 支
柱 pillar中空支柱 hollow pillar 立柱
stanchions4) 机座及
机座纵桁 engine seat and engine
girder(1) 单底构造
single bottom (2) 主机纵桁 engine
girder (3) 肋板 floor(4)
内底 tank top (5) 双层底构造
double bottom2.12 舱壁
bulkhead1) 按其适用性分水密舱壁
watertight bulkhead
油密舱壁 oiltight bulkhead气密舱壁
airtight bulkhead 耐
火舱壁 fireproof bulkhead2)
按其方向性分横壁
transverse bulkhead 纵壁 longitudinal
bulkhead3) 按其位
置分 termed by position(1)
艏尖舱后横壁或称防撞舱壁
fore peak tank aft bulkhead or
collision bulkhead (2) 艉尖
舱前横壁 aft peak
bulkhead(3) 货舱横壁 hold bulkhead (4)
甲板间舱壁 tween
deck bulkhead(5) 机舱前横壁 engine
room front
bulkhead(6) 机舱后横壁 engine room aft
bulkhead(7)
艏楼端壁, 或称艏楼后端壁 superstructure
end bulkhead, or
F’cle aft bulkhead(8) 舱壁凹处 bulkhead
recess(9)
轴隧 shaft tunnel(10) 锚链舱 chain locker4)
按
其构造分平板型舱壁 plane bulkhead 槽型壁 corrugated
bulkhead部分横壁 partial bulkhead 甲板间舱壁 tween
deck bulkhead货舱横壁 hold bulkhead 垂直扶强材
vertical stiffener 二层甲板tween deck2.13
扶强材的端部
连接方式横壁扶强材的端部连接削斜 snip 顶焊 lug 肘板
连接
bracket