纸箱甩箱测试英文翻译测试步骤
余年寄山水
580次浏览
2021年01月17日 01:53
最佳经验
本文由作者推荐
关于海豚的图片-坚韧
纸箱甩箱测试中英文翻译
1.
Objective
目的
To reduce damage in transit through a standardized program of pre- shipment testing on the spot.
在装运前通过标准的测试程序来减少货物在运输途中的损失
.
2.
SCOPE
范围
2.1.
This test applies to all hard goods for packaged products under 201 pounds (91.17kg) when prepared
for shipment.
此项测试使用于所有准备装运的
,
包装在
201
磅
(91.17GK)
以下的坚硬货物
.
2.2.
This test is derived from ASTM Drop Test, Assurance Level III.
此项测试源自美国材料实验协会摔箱测试
,
保险标准
III
3.
EQUIPMENT NEEDED
所需设备
3.1.
tape measure (minimum 45 inches long)
卷尺
(
至少
45
英尺
)
3.2.
Balance to weigh the carton.
称纸箱重量的砰
.
3.3.
Concrete floor (minimum 2mX2m).
混凝土地面
(
至少
2MX2M)
4.
SAMPLING
取样
4.1.
Draw one carton at random by style from the shipment.
在同一款的大货中随意抽取一箱
.
4.2.
If
only
pattern/color
is
different
on
same
item,
the
inspector
can
perform
on
representative
pattern/color for drop test and its result can be referred to the others.
在同一款货物中
,
如仅是图案
/
颜色有异
,
检验员可抽取典型图案
/
颜色进行摔箱测试
,
其结果可
参考其他项目
.
5.
DROP HEIGHT
摔箱高度
Packaged Product Weight Free Fall Drop Height
完整包装重量
自由降落高度
1 (4.54kgs) Thru 20.99 Pounds (9.52kgs) 30 inches (76.20cms)
1(4.54kgs)
—
20.99
磅
(9.52kgs) 30
英寸
(76.20cms)
21 (9.53kgs) Thru 40.99 Pounds (18.59kgs) 24 inches (60.96cms)
21(9.53kgs)
—
40.99
磅
(18.59kgs) 24
英寸
(60.96cms)
41 (18.60kgs) Thru 60.99 Pounds (27.66kgs) 18 inches(45.72cms)
41(18.60kgs)
—
60.99
磅
(27.66kgs) 18
英寸
(45.72cms)
61 (27.67kgs) Thru 100.00 pounds (45.36kgs) 12 inches (30.48cms)
61(27.67kgs)-100.00
磅
(45.36kgs) 12
英寸
(30.48cms)
101 (36.74kgs) Thru 150.00 Pounds (45.81kgs) 8 inches (20.3cm)
101(36.74kgs)
—
150
磅
(45.81kgs) 8
英寸
(20.3cms)
6.
TEST PROCEDURE
Confidential
Page 1 of 4
测试程序
6.1.
Before
performing
drop
test,
the
inspector
should
inspect
all
pieces
in
the
carton
for
testing
and
make sure the goods in the carton has no damage or breakage. If any piece has damage or breakage
before testing, the inspector should mark at defect area on the sample to identify them after drop test,
and record it on the report.
进行测试之前
,
检验员应先检验每一箱用来测试的货物
,
确保其是完好无损的
.
若在测试前发
现任何一件有损坏
,
检验员应在那件样品上标出损坏的地方
,
以便摔箱测试以后能分辨出来
,
并情况记录在报告上
.
6.2.
Repack the carton.
重新包装好
.
6.3.
Perform the drop test, in accordance with height prescribed on point 5., in the following sequence:
为了符合上述第
5
点要求
,
按照以下步骤进行摔箱测试
.
6.3.1.
Test the corner of most fragile face which is near to the manufacturer
’
s joint.
测试最脆弱的一角
,
靠近纸箱接合处的一面
.
Manufactory's Joint/
接口处
1st Drop/
第一次摔箱
6.3.2.
The shortest edge radiating from the corner tested.
由已测试的那一角辐射出来最短的一边
Manufactory's Joint/
接口处
2nd Drop/
第二次摔箱
6.3.3.
The next longest edge from the corner tested.
由已测试的那一角辐射出来次长的一边
6.3.4.
The longest edge radiating from the corner tested.
由已测试的那一角辐射出来最长的一边
3rd drop/
第三次摔箱
4th Drop/
第四次摔箱
6.3.5.
Flat on one of the smallest face.
面积最小的其中一面
6.3.6.
Flat on the opposite small face.
Confidential
Page 2 of 4